旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
ASA FXTW30PE 挤出级,优秀的耐候性
  • 产 品:ASA FXTW30PE 挤出级,优秀的耐候性
  • 产 地:沙伯基础创新
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

Geloy* Resin
Geloy Weatherable
Geloy* advanced amorphous terpolymer of acrylic-styrene-acrylonitrile (ASA) resins are among the most weatherable grades in SABIC Innovative Plastics' portfolio. In addition to exterior stability, advanced grades of Geloy resin and blends offer great aesthetics, color options, good chemical resistance, high heat performance, and processability.

Geloy* Resin ASA FXTW30PE 数据
Pearlescent GELOY ASA resin with copper-look for capstock extrusion. Outstanding weatherability.

Property
TYPICAL PROPERTIES (1)

MECHANICAL Value Unit  Standard 
Tensile Stress,yld,Type I,5 mm/min 500 kgf/cm² ASTM D 638
Tensile Stress,brk,Type I,5 mm/min 390 kgf/cm² ASTM D 638
Tensile Strain,yld,Type I,5 mm/min 3.3 % ASTM D 638
Tensile Strain,brk,Type I,5 mm/min 14 % ASTM D 638
Tensile Modulus,5 mm/min 27200 kgf/cm² ASTM D 638
Flexural Stress,yld,1.3 mm/min,50 mm span 780 kgf/cm² ASTM D 790
Flexural Modulus,1.3 mm/min,50 mm span 28000 kgf/cm² ASTM D 790
Tensile Stress,yield,5 mm/min 50 MPa ISO 527
Tensile Stress,break,5 mm/min 48 MPa ISO 527
Tensile Strain,yield,5 mm/min 3.6 % ISO 527
Tensile Strain,break,5 mm/min 29 % ISO 527
Tensile Modulus,1 mm/min 2750 MPa ISO 527
Flexural Stress,yield,2 mm/min 76 MPa ISO 178
Flexural Modulus,2 mm/min 2780 MPa ISO 178
IMPACT Value Unit  Standard 
Izod Impact,notched,23℃ 6 cm-kgf/cm ASTM D 256
Izod Impact,notched,-30℃ 3 cm-kgf/cm ASTM D 256
Instrumented Impact Total Energy,23℃ 40 cm-kgf ASTM D 3763
Izod Impact,notched 80*10*4 +23℃ 6 kJ/m² ISO 180/1A
Izod Impact,notched 80*10*4 -30℃ 3 kJ/m² ISO 180/1A
THERMAL Value Unit  Standard 
Vicat Softening Temp,Rate B/50 89 ASTM D 1525
HDT,1.82 MPa,3.2mm,unannealed 76 ASTM D 648
CTE,-40℃ to 40℃,flow 9.54E-05 1/℃ ISO 11359-2
CTE,-40℃ to 40℃,xflow 1.08E-04 1/℃ ISO 11359-2
Vicat Softening Temp,Rate B/50 86 ISO 306
HDT/Af,1.8 MPa Flatw 80*10*4 sp=64mm 78 ISO 75/Af
PHYSICAL Value Unit  Standard 
Specific Gravity 1.14 - ASTM D 792
Mold Shrinkage,flow,3.2 mm (5) 0-0.1 % SABIC Method
Melt Flow Rate,200℃/3.8 kgf 0.6 g/10 min ASTM D 1238
Density 1.12 g/cm³ ISO 1183
Source GMD,last updated:2009/08/21

• Barrel temperatures should be banked TO 150℃ (300℉)

Parameter Sheet Extrusion Value Unit 
Drying Temperature 80-90
Drying Time 3-4 hrs
Drying Time (Cumulative) 12 hrs
Minimum Moisture Content 0.04 %
Melt Temperature 220-245
Barrel-Zone 1 Temperature 180-225
Barrel-Zone 2 Temperature 190-230
Barrel-Zone 3 Temperature 205-240
Barrel-Zone 4 Temperature 210-245
Adapter Temperature 210-245
Die Temperature 210-245
Roll Stack Temp-Top 70-100
Roll Stack Temp-Middle 70-95
Roll Stack Temp-Bottom 65-90
Source GMD,last updated:2009/08/21

• Purge using HIPS or Ultra HDPE.

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.

(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for selection purposes. Not to be used for part or tool design.
(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
ASA FXTW30PE 沙伯基础创新ASA塑料代理:http://www.pa66-suliao.com/product/tysuliao/SAN/