旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PE FX04491H 含硅胶,内部润滑
  • 产 品:PE FX04491H 含硅胶,内部润滑
  • 产 地:美国液氮
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

LNP Lubricomp* Olefins Compound
Enhanced wear resistance, lower friction for key r
Olefinic LNP Lubricomp compounds offer enhanced wear resistance and lower friction to key resins by combining them with internal lubricants. Glass and carbon fibers can also be included for improved strength and stiffness.

LNP™ Lubricomp™ Compound PE FX04491H 塑料物性

Also known as:LNP™ Lubricomp™ Compound PDX-F-04491
Product reorder name:FX04491H
LNP LUBRICOMP* FX04491H is a compound based on Polyethylene resin containing Silicone. Added features of this material include: Internally Lubricated.

MECHANICAL Value Unit Standard
Tensile Stress,yield 250 kgf/cm² ASTM D 638
Tensile Strain,yield 7.4 % ASTM D 638
Flexural Stress 230 kgf/cm² ASTM D 790
Flexural Modulus 108900 kgf/cm² ASTM D 790
IMPACT Value Unit Standard
Izod Impact,unnotched,23℃ NB cm-kgf/cm ASTM D 4812
Izod Impact,notched,23℃ 4 cm-kgf/cm ASTM D 256
THERMAL Value Unit Standard
HDT,1.82 MPa,3.2mm,unannealed 42 ASTM D 648
PHYSICAL Value Unit Standard
Density 0.932 g/cm³ ASTM D 792
Mold Shrinkage,flow,24 hrs(5) 2.4 % ASTM D 955
Mold Shrinkage,xflow,24 hrs(5) 1.6 % ASTM D 955
Wear Factor Washer 24 10^-10 in^5-min/ft-lb-hr ASTM D 3702 Modified
Dynamic COF 0.13 - ASTM D 3702 Modified
Static COF 0.11 - ASTM D 3702 Modified
Source GMD,last updated:2004/09/30
Parameter Injection Molding Value Unit
Drying Temperature 80
Drying Time 4 hrs
Melt Temperature 230
Front-Zone 3 Temperature 220-230
Middle-Zone 2 Temperature 210-220
Rear-Zone 1 Temperature 195-205
Mold Temperature 40-55
Back Pressure 0.2-0.3 MPa
Screw Speed 30-60 rpm
Source GMD,last updated:2004/09/30

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics

1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

关健字:【LNP™ Lubricomp™ Compound PE FX04491H