旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PPS OCP36A 含聚四氟乙烯,碳纤,硅酮,润滑,导电级
  • 产 品:PPS OCP36A 含聚四氟乙烯,碳纤,硅酮,润滑,导电级
  • 产 地:美国液氮
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

LNP Lubricomp* High Temperature Resins Compound
Adding friction control & wear resistance
High temperature LNP Lubricomp compounds provide Improved wear resistance and lower friction by combining internal lubricants with high performance base resins. Glass and carbon fibers can also be included for improved strength and stiffness.

LNP™ Lubricomp™ Compound PPS OCP36A 塑料物性

Also known as:LNP™ Lubricomp™ Compound OCL-4536
Product reorder name:OCP36A
LNP* Lubricomp* OCL-4536 is a compound based on PPS - Branched resin containing PTFE, Carbon Fiber, Silicone. Added features of this material include: Internally Lubricated, Electrically Conductive.

MECHANICAL Value Unit Standard
Tensile Stress,yield 1300 kgf/cm² ASTM D 638
Tensile Stress,break 1210 kgf/cm² ASTM D 638
Tensile Strain,yield 0.9 % ASTM D 638
Tensile Strain,break 1.6 % ASTM D 638
Tensile Modulus,50mm/min 189800 kgf/cm² ASTM D 638
Flexural Stress 2340 kgf/cm² ASTM D 790
Flexural Modulus 205200 kgf/cm² ASTM D 790
Tensile Stress,yield 113 MPa ISO 527
Tensile Stress,break 113 MPa ISO 527
Tensile Strain,yield 0.7 % ISO 527
Tensile Strain,break 0.7 % ISO 527
Tensile Modulus,1mm/min 19880 MPa ISO 527
Flexural Stress 176 MPa ISO 178
Flexural Modulus 19000 MPa ISO 178
IMPACT Value Unit Standard
Izod Impact,unnotched,23℃ 32 cm-kgf/cm ASTM D 4812
Izod Impact,notched,23℃ 3 cm-kgf/cm ASTM D 256
Instrumented Impact Energy @ peak,23℃ 64 cm-kgf ASTM D 3763
Multiaxial Impact 15 cm-kgf ISO 6603
Izod Impact,unnotched 80*10*4 +23℃ 13 kJ/m² ISO 180/1U
Izod Impact,notched 80*10*4 +23℃ 3 kJ/m² ISO 180/1A
THERMAL Value Unit Standard
HDT,0.45 MPa,3.2mm,unannealed 273 ASTM D 648
HDT,1.82 MPa,3.2mm,unannealed 258 ASTM D 648
CTE,-40℃ to 40℃,flow 3.60E-05 1/℃ ASTM E 831
CTE,-40℃ to 40℃,xflow 7.20E-06 1/℃ ASTM E 831
CTE,-40℃ to 40℃,flow 3.60E-05 1/℃ ISO 11359-2
CTE,-40℃ to 40℃,xflow 7.00E-06 1/℃ ISO 11359-2
HDT/Bf,0.45 MPa Flatw 80*10*4 sp=64mm 272 ISO 75/Bf
HDT/Af,1.8 MPa Flatw 80*10*4 sp=64mm 248 ISO 75/Af
PHYSICAL Value Unit Standard
Density 1.49 g/cm³ ASTM D 792
Moisture Absorption,50% RH,24 hrs - % ASTM D 570
Mold Shrinkage,flow,24 hrs(5) 0.2 % ASTM D 955
Mold Shrinkage,xflow,24 hrs(5) 0.7 % ASTM D 955
Mold Shrinkage,flow,24 hrs(5) 0.15 % ISO 294
Mold Shrinkage,xflow,24 hrs(5) 0.66 % ISO 294
Wear Factor Washer 15 10^-10 in^5-min/ft-lb-hr ASTM D 3702 Modified
Dynamic COF 0.36 - ASTM D 3702 Modified
Static COF 0.3 - ASTM D 3702 Modified
Density 1.53 g/cm³ ISO 1183
Source GMD,last updated:2007/05/12
Parameter Injection Molding Value Unit
Drying Temperature 120-150
Drying Time 4 hrs
Melt Temperature 315-320
Front-Zone 3 Temperature 330-345
Middle-Zone 2 Temperature 320-330
Rear-Zone 1 Temperature 305-315
Mold Temperature 140-165
Back Pressure 0.2-0.3 MPa
Screw Speed 30-60 rpm
Source GMD, last updated:2007/05/12

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics

1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

关健字:【LNP™ Lubricomp™ Compound PPS OCP36A