旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PPO IGN320 玻纤20%增强,高热量,高模量
  • 产 品:PPO IGN320 玻纤20%增强,高热量,高模量
  • 产 地:沙伯基础创新
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

Noryl* Reinforced, Multi-purpose Resin
Strong, Balanced, Dimensionally Stable
General purpose, reinforced modified amorphous blends of PPO* resin (polyphenylene ether) and polystyrene.

Noryl* Resin IGN320 数据表

20% glass reinforced PPE + PS. High heat, high modulus automotive applications like ignition coils.

Property
TYPICAL PROPERTIES(1)

MECHANICAL Value Unit  Standard 
Tensile Stress,yld,Type I,5mm/min 1110 kgf/cm² ASTM D 638
Tensile Stress,brk,Type I,5mm/min 1110 kgf/cm² ASTM D 638
Tensile Strain,brk,Type I,5mm/min 2.4 % ASTM D 638
Tensile Modulus,5mm/min 63800 kgf/cm² ASTM D 638
Flexural Stress,brk,1.3mm/min,50mm span 1730 kgf/cm² ASTM D 790
Flexural Modulus,1.3mm/min,50mm span 58300 kgf/cm² ASTM D 790
IMPACT Value Unit  Standard 
Izod Impact,unnotched,23℃ 52 cm-kgf/cm ASTM D 4812
Izod Impact,notched,23℃ 10 cm-kgf/cm ASTM D 256
Instrumented Impact Total Energy,23℃ 168 cm-kgf ASTM D 3763
THERMAL Value Unit  Standard 
Vicat Softening Temp,Rate B/50 175 ASTM D 1525
HDT,0.45 MPa,3.2mm,unannealed 164 ASTM D 648
HDT,1.82 MPa,3.2mm,unannealed 158 ASTM D 648
PHYSICAL Value Unit  Standard 
Specific Gravity 1.2 - ASTM D 792
Mold Shrinkage,flow,3.2mm (5) 0.1-0.3 % SABIC Method
Mold Shrinkage,xflow,3.2mm (5) 0.2-0.4 % SABIC Method
Melt Flow Rate,300℃/5.0 kgf 12.8 g/10 min ASTM D 1238
ELECTRICAL Value Unit  Standard 
Dielectric Strength,in oil,1.6mm 33.9 kV/mm ASTM D 149
Source GMD,last updated:2011/08/01
Parameter Injection Molding Value Unit 
Drying Temperature 110-120
Drying Time 3-4 hrs
Drying Time (Cumulative) 8 hrs
Maximum Moisture Content 0.02 %
Melt Temperature 300-325
Nozzle Temperature 300-325
Front-Zone 3 Temperature 290-325
Middle-Zone 2 Temperature 275-320
Rear-Zone 1 Temperature 265-315
Mold Temperature 80-110
Back Pressure 0.3-0.7 MPa
Screw Speed 20-100 rpm
Shot to Cylinder Size 30-70 %
Source GMD,last updated:2011/08/01

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics
1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

关健字:Noryl* Resin PPO IGN320

湘樟塑化版权所有:http://www.pa66-suliao.com/