快速查找
主营塑料
产品推荐
- ⊕PPS OL003A 含玻璃纤维,聚四氟乙
- ⊕PBT 420SE0 玻纤30%增强,阻燃级
- ⊕PBT 310SE0 非增强型,PBT阻燃树脂
- ⊕PP HJ730 高流动,高钢性,高耐热
- ⊕PP FB71U6 耐热级,抗UV,阻燃级
- ⊕PA6 73G30L NC010 玻璃纤维30%增
- ⊕PA66 70G43L NC010 玻璃纤维43%增
- ⊕PA66 70G33L NC010 玻璃纤维33%增
- ⊕PA66 70G30L NC010 玻璃纤维30%增
- ⊕PA66 80G33L NC010 玻纤33%增强,
- ⊕PA66 FR50 NC010A 玻纤25%增强,阻
- ⊕POM 900P NC010 低粘度,热稳定,低
- ⊕POM 500P NC010 中高粘,热稳定,低
- ⊕POM 100P NC010 高粘度,韧性好,热
- ⊕PBT SK605 NC010 玻璃纤维30%增强
- ⊕PA66 1300G 玻纤增强级
联系我们
- 产 品：PPO FN150X 阻燃级,生产率提高
- 产 地：沙伯基础创新
- 价 格：电话报价
- 库 存：20吨
- 交 货：江苏苏州
- 苏州希普能：185 5121 3137 谭经理
Noryl* Foam Resin
Light, Stiff, Energy Absorbing
Foamable amorphous resins of PPO* resin (polyphenylene ether) and polystyrene
Noryl* Resin FN150X 英文物性表
Improved reliability and productivity. Thin wall capability. UL94 V-0/5VA rated. All data at 20% weight reduction and 0.250" wall.
Property
TYPICAL PROPERTIES (1)
| MECHANICAL | Value | Unit | Standard |
| FOAM-MECHANICAL 6.4mm Wt Reduction | 20 | % | - |
| Tensile Stress,yield,6.35mm | 280 | kgf/cm² | ASTM D 638 |
| Tensile Stress,break,6.35mm | 280 | kgf/cm² | ASTM D 638 |
| Tensile Strain,yield,6.35mm | 7.3 | % | ASTM D 638 |
| Tensile Strain,break,6.35mm | 14 | % | ASTM D 638 |
| Flexural Stress,yield,6.4mm | 530 | kgf/cm² | ASTM D 790 |
| Flexural Modulus,6.4mm | 17700 | kgf/cm² | ASTM D 790 |
| Hardness,Rockwell R | 121 | - | ASTM D 785 |
| Taber Abrasion,CS-17,1 kg | 152 | mg/1000cy | ASTM D 1044 |
| IMPACT | Value | Unit | Standard |
| FOAM-IMPACT 6.4mm Wt Reduction | 20 | % | - |
| Izod Impact,unnotched,23℃,6.4mm | 34 | cm-kgf/cm | ASTM D 4812 |
| THERMAL | Value | Unit | Standard |
| FOAM-THERMAL 6.4mm Wt Reduction | 20 | % | - |
| Vicat Softening Temp,Rate B/50 | 110 | ℃ | ASTM D 1525 |
| HDT,0.45 MPa,6.4mm,unannealed | 89 | ℃ | ASTM D 648 |
| HDT,1.82 MPa,6.4mm,unannealed | 73 | ℃ | ASTM D 648 |
| Relative Temp Index,Elec | 50 | ℃ | UL 746B |
| Relative Temp Index,Mech w/impact | 50 | ℃ | UL 746B |
| Relative Temp Index,Mech w/o impact | 50 | ℃ | UL 746B |
| PHYSICAL | Value | Unit | Standard |
| FOAM-PHYSICAL 6.4mm Wt Reduction | 20 | % | - |
| Specific Gravity ppo | 1.12 | - | ASTM D 792 |
| Water Absorption,24 hours | 0.06 | % | ASTM D 570 |
| Mold Shrinkage,flow,6.4mm (5) | 0.6-0.8 | % | SABIC Method |
| Mold Shrinkage,xflow,6.4mm (5) | 0.6-0.8 | % | SABIC Method |
| FLAME CHARACTERISTICS | Value | Unit | Standard |
| FOAM-Flame Class Minimum Density | 0.9 | g/cm³ | - |
| UL Recognized,94V-0 Flame Class Rating (3) | 3.98 | mm | UL 94 |
| UL Recognized,94-5VA Rating (3) | 3.98 | mm | UL 94 |
| Radiant Panel Listing | YES | - | UL Tested |
| Source GMD,last updated:1992/07/01 | |||
| Parameter Structural Foam Molding | Value | Unit |
| Blowing Agent,Physical System | Nitrogen Gas | - |
| Concentration Range (Blowing Agent) | 1-3 | % |
| Recommended Concentration (Blowing Agent) | 2 | % |
| Drying Temperature (Resin) | 70-80 | ℃ |
| Drying Time (Resin) | 2-4 | hrs |
| Drying Time (Resin,Cumulative) | 8 | hrs |
| Melt Temperature | 270-310 | ℃ |
| Nozzle Temperature | 270-305 | ℃ |
| Front Temperature | 270-305 | ℃ |
| Middle Temperature | 270-305 | ℃ |
| Rear Temperature | 230-260 | ℃ |
| Mold Temperature | 25-55 | ℃ |
| Source GMD,last updated:1992/07/01 | ||
• Drying is not required/recommended.
THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics
1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、 Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
关健字：Noryl* Resin PPO FN150X
湘樟塑化版权所有