快速查找
主营塑料
产品推荐
- ⊕PPS OL003A 含玻璃纤维,聚四氟乙
- ⊕PBT 420SE0 玻纤30%增强,阻燃级
- ⊕PBT 310SE0 非增强型,PBT阻燃树脂
- ⊕PP HJ730 高流动,高钢性,高耐热
- ⊕PP FB71U6 耐热级,抗UV,阻燃级
- ⊕PA6 73G30L NC010 玻璃纤维30%增
- ⊕PA66 70G43L NC010 玻璃纤维43%增
- ⊕PA66 70G33L NC010 玻璃纤维33%增
- ⊕PA66 70G30L NC010 玻璃纤维30%增
- ⊕PA66 80G33L NC010 玻纤33%增强,
- ⊕PA66 FR50 NC010A 玻纤25%增强,阻
- ⊕POM 900P NC010 低粘度,热稳定,低
- ⊕POM 500P NC010 中高粘,热稳定,低
- ⊕POM 100P NC010 高粘度,韧性好,热
- ⊕PBT SK605 NC010 玻璃纤维30%增强
- ⊕PA66 1300G 玻纤增强级
联系我们
- 产 品：PPO WCD891B 无卤阻燃,电线电缆应用
- 产 地：沙伯基础创新
- 价 格：电话报价
- 库 存：20吨
- 交 货：江苏苏州
- 苏州希普能：185 5121 3137 谭经理
Noryl* Flexible Noryl Resin
Flexible and non Halogenated
Flexible materials comprised of PPO™ resin (polyphenylene ether) and TPE's (thermoplastic elastomers) are commonly used for wire, cable and jacket insulation.
Noryl* Resin WCD891B 英文物性表
Non-halogenated flame retardant, flexible Noryl resin intended for evaluation in wire and cable applications. Strong flame retardant performance capable of meeting VW-1 and 80℃ end use temperature requirements as defined by UL 1581. 89 Shore A hardness. Good processing by using standard extrusion equipment. UL1581 tests conducted on 2.0 mm wire with 0.12 mm x 20 stranded copper conductor.
Property
TYPICAL PROPERTIES (1)
| MECHANICAL | Value | Unit | Standard |
| Tensile Stress, brk, Type I, 50mm/min | 160 | kgf/cm² | ASTM D 638 |
| Tensile Strain, brk, Type I, 50mm/min | 170 | % | ASTM D 638 |
| Flexural Modulus, 12.5mm/min, 100mm span | 1600 | kgf/cm² | ASTM D 790 |
| Hardness, Shore A, 30S reading | 89 | - | ASTM D 2240 |
| Tensile Stress, break, 50mm/min | 15 | MPa | ISO 527 |
| Tensile Strain, yield, 50mm/min | 140 | % | ISO 527 |
| Flexural Modulus, 12.5mm/min | 140 | MPa | ISO 178 |
| Tear strength | 7 | N/mm | ISO 6383 |
| IMPACT | Value | Unit | Standard |
| Brittleness Temperature | <-40 | ℃ | ASTM D 746 |
| PHYSICAL | Value | Unit | Standard |
| Specific Gravity | 1.1 | - | ASTM D 792 |
| Melt Flow Rate, 250℃/5.0 kgf | 20 | g/10 min | ASTM D 1238 |
| ELECTRICAL | Value | Unit | Standard |
| Volume Resistivity | 1.50E+15 | Ohm-cm | ASTM D 257 |
| Surface Resistivity | 5.10E+15 | Ohm | ASTM D 257 |
| Dielectric strength in oil, 2.0mm | 24 | kV/mm | IEC 60243-1 |
| Relative Permittivity, 1 MHz | 2.9 | - | IEC 60250 |
| Dissipation Factor, 1 MHz | 0.04 | - | IEC 60250 |
| Comparative Tracking Index | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Value | Unit | Standard |
| UL Compliant, 94V-0 Flame Class Rating (3)(4) | 4 | mm | UL 94 by SABIC-IP |
| Glow Wire Flammability Index 850℃, passes at | 3 | mm | IEC 60695-2-12 |
| Glow Wire Ignitability Temperature, 3.0mm | 750 | ℃ | IEC 60695-2-13 |
| Oxygen Index (LOI) | 27 | % | ISO 4589 |
| WIRE AND CABLE-UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper | Value | Unit | Standard |
| Tensile strength @ break | 18 | MPa | UL 1581 |
| Tensile elongation @ break | 215 | % | UL 1581 |
| Tensile strength @ break after 7days @113℃ | 21 | MPa | UL 1581 |
| Tensile elongation @ break after 7days @113℃ | 160 | % | UL 1581 |
| UL temperature rating | 80 | ℃ | UL 1581 |
| Heat Deformation at 100℃/250g | 9 | % | UL 1581 |
| VW-1 | Pass | - | UL 1581 |
| Source GMD, last updated:2007/07/06 | |||
| Parameter Wire Coating Extrusion | Value | Unit |
| Drying Temperature | 75-85 | ℃ |
| Drying Time | 5-7 | hrs |
| Drying Time (Cumulative) | 12 | hrs |
| Maximum Moisture Content | 0.02 | % |
| Extruder Length/Diameter Ratio (L/D) | 22:1 to 26:1 | - |
| Screw Speed | 15-85 | rpm |
| Feed Zone Temperature | 180-220 | ℃ |
| Middle Zone Temperatures | 220-250 | ℃ |
| Head Zone Temperature | 220-250 | ℃ |
| Neck Temperature | 220-250 | ℃ |
| Cross-head Temperature | 220-250 | ℃ |
| Die Temperature | 220-250 | ℃ |
| Melt Temperature | 220-250 | ℃ |
| Conductor Pre-heat Temperature | 25-120 | ℃ |
| Screen Pack | 150-100 | - |
| Cooling Water Air Gap | 100-200 | mm |
| Water Bath Temperature | 15-60 | ℃ |
| Source GMD,last updated:2007/07/06 | ||
• NOTE: Recommended Drying Parameters are based on usage of Dehumidify Drying / Drying Oven.
THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.
1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、 Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
关健字：Noryl* Resin PPO WCD891B 链接：光扩散PC_PC光扩散塑料_LED灯罩灯管材料_PC