Cycoloy* Visualfx* Resin
Tough Yet Beautiful
Cycoloy PC/ABS Visualfx Resins provide molded-in effects that can eliminate the need for modifications after molding while still offering the impact and processing advantage that Cycoloy Resin is known for. This can provide cleaner and more vibrant part aesthetics that will last as long as the part lasts. Visualfx Resins include Sparkle and Porcelain effects as well as several metallic and natural material effects. Available in a variety of colors and base resins.

Cycoloy* Resin PC/ABS CY2000 数据
Cycoloy resin CY2000 is a flame retardant (FR) PC/ABS blend free from halogen containing FR agents. It was designed to meet CA133 application requirements.

Property
TYPICAL PROPERTIES (1)

MECHANICAL	Value	Unit	Standard
Tensile Stress,yld,Type I,50mm/min	640	kgf/cm²	ASTM D 638
Tensile Stress,brk,Type I,50mm/min	480	kgf/cm²	ASTM D 638
Tensile Strain,yld,Type I,50mm/min	4	%	ASTM D 638
Tensile Strain,brk,Type I,50mm/min	99	%	ASTM D 638
Tensile Modulus,50mm/min	29200	kgf/cm²	ASTM D 638
Flexural Stress,yld,1.3mm/min,50mm span	1000	kgf/cm²	ASTM D 790
Flexural Modulus,1.3mm/min,50mm span	28200	kgf/cm²	ASTM D 790
IMPACT	Value	Unit	Standard
Izod Impact,notched,23℃	45	cm-kgf/cm	ASTM D 256
Izod Impact,notched,-30℃	9	cm-kgf/cm	ASTM D 256
Instrumented Impact Total Energy,23℃	642	cm-kgf	ASTM D 3763
THERMAL	Value	Unit	Standard
Vicat Softening Temp,Rate B/50	92	℃	ASTM D 1525
HDT,1.82 MPa,3.2mm,unannealed	78	℃	ASTM D 648
CTE,-40℃ to 40℃,flow	6.17E-05	1/℃	ASTM E 831
CTE,-40℃ to 40℃,xflow	7.09E-05	1/℃	ASTM E 831
PHYSICAL	Value	Unit	Standard
Specific Gravity	1.18	-	ASTM D 792
Mold Shrinkage,flow,3.2mm(5)	0.44-0.54	%	SABIC Method
Melt Flow Rate,260℃/2.16 kgf	21	g/10 min	ASTM D 1238
Source GMD,last updated:2007/12/04

Parameter Injection Molding	Value	Unit
Drying Temperature	75-80	℃
Drying Time	3-4	hrs
Drying Time(Cumulative)	8	hrs
Maximum Moisture Content	0.04	%
Melt Temperature	230-275	℃
Nozzle Temperature	230-275	℃
Front-Zone 3 Temperature	225-275	℃
Middle-Zone 2 Temperature	215-260	℃
Rear-Zone 1 Temperature	210-255	℃
Mold Temperature	50-70	℃
Back Pressure	0.3-0.7	MPa
Screw Speed	40-70	rpm
Shot to Cylinder Size	30-80	%
Vent Depth	0.038-0.076	mm
Source GMD,last updated:2007/12/04

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.

(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for selection purposes. Not to be used for part or tool design.
(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
PC/ABS合金塑料报价网：http://www.pa66-suliao.com/product/gcsuliao/PC/ABS/