Cycoloy* Visualfx* Resin
Tough Yet Beautiful
Cycoloy PC/ABS Visualfx Resins provide molded-in effects that can eliminate the need for modifications after molding while still offering the impact and processing advantage that Cycoloy Resin is known for. This can provide cleaner and more vibrant part aesthetics that will last as long as the part lasts. Visualfx Resins include Sparkle and Porcelain effects as well as several metallic and natural material effects. Available in a variety of colors and base resins.

Cycoloy* Resin EHA 数据
PC+ABS. Electroplateable.

Property
TYPICAL PROPERTIES (1)

MECHANICAL	Value	Unit	Standard
Tensile Stress,yld,Type I,50mm/min	460	kgf/cm²	ASTM D 638
Tensile Modulus,50mm/min	24600	kgf/cm²	ASTM D 638
Flexural Stress,yld,1.3mm/min,50mm span	800	kgf/cm²	ASTM D 790
Flexural Modulus,1.3mm/min,50mm span	26000	kgf/cm²	ASTM D 790
Hardness,Rockwell R	111	-	ASTM D 785
IMPACT	Value	Unit	Standard
Izod Impact,notched,23℃	37	cm-kgf/cm	ASTM D 256
Izod Impact,notched,-30℃	6	cm-kgf/cm	ASTM D 256
THERMAL	Value	Unit	Standard
CTE,-40℃ to 40℃,flow	6.30E-05	1/℃	ASTM E 831
Specific Heat	2	J/g-℃	ASTM C 351
Thermal Conductivity	0.2	W/m-℃	ASTM E 1530
Relative Temp Index,Elec	60	℃	UL 746B
Relative Temp Index,Mech w/impact	60	℃	UL 746B
Relative Temp Index,Mech w/o impact	60	℃	UL 746B
PHYSICAL	Value	Unit	Standard
Specific Gravity	1.09	-	ASTM D 792
Mold Shrinkage,flow,3.2mm(5)	0.5-0.8	%	SABIC Method
ELECTRICAL	Value	Unit	Standard
Arc Resistance,Tungsten{PLC}	6	PLC Code	ASTM D 495
Hot Wire Ignition{PLC)	3	PLC Code	UL 746A
High Voltage Arc Track Rate{PLC}	3	PLC Code	UL 746A
High Ampere Arc Ign,surface{PLC}	0	PLC Code	UL 746A
Comparative Tracking Index(UL){PLC}	0	PLC Code	UL 746A
FLAME CHARACTERISTICS	Value	Unit	Standard
UL Recognized,94HB Flame Class Rating(3)	1.47	mm	UL 94
Source GMD,last updated:2000/01/05

Parameter Injection Molding	Value	Unit
Drying Temperature	105-115	℃
Drying Time	3-4	hrs
Drying Time (Cumulative)	8	hrs
Maximum Moisture Content	0.04	%
Melt Temperature	260-275	℃
Nozzle Temperature	245-260	℃
Front-Zone 3 Temperature	255-275	℃
Middle-Zone 2 Temperature	245-260	℃
Rear-Zone 1 Temperature	220-230	℃
Mold Temperature	70-95	℃
Back Pressure	0.3-0.7	MPa
Screw Speed	20-60	rpm
Shot to Cylinder Size	50-70	%
Vent Depth	0.038-0.076	mm
Source GMD,last updated:2000/01/05

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.

(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for selection purposes. Not to be used for part or tool design.
(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
PC/ABS合金塑料报价网：http://www.pa66-suliao.com/product/gcsuliao/PC/ABS/