快速查找
主营塑料
产品推荐
- ⊕PPS OL003A 含玻璃纤维,聚四氟乙
- ⊕PBT 420SE0 玻纤30%增强,阻燃级
- ⊕PBT 310SE0 非增强型,PBT阻燃树脂
- ⊕PP HJ730 高流动,高钢性,高耐热
- ⊕PP FB71U6 耐热级,抗UV,阻燃级
- ⊕PA6 73G30L NC010 玻璃纤维30%增
- ⊕PA66 70G43L NC010 玻璃纤维43%增
- ⊕PA66 70G33L NC010 玻璃纤维33%增
- ⊕PA66 70G30L NC010 玻璃纤维30%增
- ⊕PA66 80G33L NC010 玻纤33%增强,
- ⊕PA66 FR50 NC010A 玻纤25%增强,阻
- ⊕POM 900P NC010 低粘度,热稳定,低
- ⊕POM 500P NC010 中高粘,热稳定,低
- ⊕POM 100P NC010 高粘度,韧性好,热
- ⊕PBT SK605 NC010 玻璃纤维30%增强
- ⊕PA66 1300G 玻纤增强级
联系我们
- 产 品：PC/ABS LG8002 低光泽度,高抗冲击
- 产 地：沙伯基础创新
- 价 格：电话报价
- 库 存：20吨
- 交 货：江苏苏州
- 苏州希普能：185 5121 3137 谭经理
Cycoloy* Resin PC/ABS LG8002
Automotive. Low gloss, high impact and ductility at 73F and -22F. UV-stable colors.
Property
TYPICAL PROPERTIES (1)
| MECHANICAL | Value | Unit | Standard |
| Tensile Stress,yld,Type I,50mm/min | 560 | kgf/cm² | ASTM D 638 |
| Tensile Strain,yld,Type I,50mm/min | 5 | % | ASTM D 638 |
| Tensile Strain,brk,Type I,50mm/min | 120 | % | ASTM D 638 |
| Flexural Stress,yld,1.3mm/min,50mm span | 870 | kgf/cm² | ASTM D 790 |
| Flexural Modulus,1.3mm/min,50mm span | 23200 | kgf/cm² | ASTM D 790 |
| IMPACT | Value | Unit | Standard |
| Izod Impact,notched,23℃ | 65 | cm-kgf/cm | ASTM D 256 |
| Izod Impact,notched,-30℃ | 59 | cm-kgf/cm | ASTM D 256 |
| Instrumented Impact Total Energy,23℃ | 483 | cm-kgf | ASTM D 3763 |
| Instrumented Impact Total Energy,-30℃ | 414 | cm-kgf | ASTM D 3763 |
| THERMAL | Value | Unit | Standard |
| HDT,0.45 MPa,3.2mm,unannealed | 121 | ℃ | ASTM D 648 |
| HDT,1.82 MPa,3.2mm,unannealed | 104 | ℃ | ASTM D 648 |
| CTE,-40℃ to 40℃,flow | 9.00E-05 | 1/℃ | ASTM E 831 |
| Thermal Conductivity | 0.25 | W/m-℃ | ASTM C 177 |
| PHYSICAL | Value | Unit | Standard |
| Specific Gravity | 1.13 | - | ASTM D 792 |
| Mold Shrinkage,flow,3.2mm(5) | 0.5-0.7 | % | SABIC Method |
| Melt Flow Rate,260℃/5.0 kgf | 6.5 | g/10 min | ASTM D 1238 |
| OPTICAL | Value | Unit | Standard |
| Gloss,untextured,60 degrees | 30 | - | ASTM D 523 |
| Source GMD,last updated:2000/01/05 | |||
| Parameter Injection Molding | Value | Unit |
| Drying Temperature | 105-110 | ℃ |
| Drying Time | 3-4 | hrs |
| Drying Time(Cumulative) | 8 | hrs |
| Maximum Moisture Content | 0.04 | % |
| Melt Temperature | 275-300 | ℃ |
| Nozzle Temperature | 275-300 | ℃ |
| Front-Zone 3 Temperature | 260-300 | ℃ |
| Middle-Zone 2 Temperature | 255-295 | ℃ |
| Rear-Zone 1 Temperature | 250-290 | ℃ |
| Mold Temperature | 60-90 | ℃ |
| Back Pressure | 0.3-0.7 | MPa |
| Screw Speed | 40-70 | rpm |
| Shot to Cylinder Size | 30-80 | % |
| Vent Depth | 0.038-0.076 | mm |
| Source GMD,last updated:2000/01/05 | ||
THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics
1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
关健字：【Cycoloy* Resin PC/ABS LG8002】
希普能塑料代理美国液氮、美国杜邦、美国舒尔曼、美国EMS、美国RTP、美国TEKNOR APEX、日本三菱工程、法国罗地亚、日本东丽、日本东洋纺织、日本宇部、日本宝理、日本旭化成、德国拜耳、德国朗盛、德国巴斯夫、荷兰DSM、瑞士EMS、台湾耐特、台湾南亚、中石化巴陵石化等尼龙PA6、PA66、POM、PBT、PPS、PA1010塑料