旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PC/ABS C6200 阻燃级
  • 产 品:PC/ABS C6200 阻燃级
  • 产 地:沙伯基础创新
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

Cycoloy* Resin PC/ABS C6200
Non-chlorinated, nombrominated flame retardant PC/ABS offering balanced heat, flow and impact to meet various application needs.

Property
TYPICAL PROPERTIES (1)

MECHANICAL Value Unit Standard
Tensile Stress,yld,Type I,50mm/min 680 kgf/cm² ASTM D 638
Tensile Strain,brk,Type I,50mm/min 50 % ASTM D 638
Flexural Stress,yld,2.6mm/min,100mm span 1050 kgf/cm² ASTM D 790
Flexural Modulus,2.6mm/min,100mm span 27400 kgf/cm² ASTM D 790
IMPACT Value Unit Standard
Izod Impact,notched,23℃ 54 cm-kgf/cm ASTM D 256
Instrumented Impact Energy @ peak,23℃ 622 cm-kgf ASTM D 3763
Instrumented Impact Energy @ peak,-30 553 cm-kgf ASTM D 3763
THERMAL Value Unit Standard
HDT,1.82 MPa,3.2mm,unannealed 87 ASTM D 648
HDT,1.82 MPa,6.4mm,unannealed 90 ASTM D 648
Relative Temp Index,Elec 85 UL 746B
Relative Temp Index,Mech w/impact 85 UL 746B
Relative Temp Index,Mech w/o impact 85 UL 746B
PHYSICAL Value Unit Standard
Specific Gravity 1.18 - ASTM D 792
Mold Shrinkage,flow,3.2mm(5) 0.4-0.6 % SABIC Method
Mold Shrinkage,xflow,3.2mm(5) 0.4-0.6 % SABIC Method
Melt Flow Rate,260℃/2.16 kgf 14.5 g/10 min ASTM D 1238
Spiral Flow,260℃,10 ips,3.175 X 1524mm 685.8 mm -
ELECTRICAL Value Unit Standard
Arc Resistance,Tungsten{PLC} 6 PLC Code ASTM D 495
Hot Wire Ignition{PLC) 2 PLC Code UL 746A
High Voltage Arc Track Rate{PLC} 3 PLC Code UL 746A
High Ampere Arc Ign,surface{PLC} 0 PLC Code UL 746A
Comparative Tracking Index(UL){PLC} 2 PLC Code UL 746A
Volume Resistivity >1.E+15 Ohm-cm IEC 60093
Surface Resistivity,ROA >1.E+15 Ohm IEC 60093
Dielectric Strength,in oil,0.8mm 35 kV/mm IEC 60243-1
Dielectric Strength,in oil,1.6mm 25 kV/mm IEC 60243-1
Dielectric Strength,in oil,3.2mm 17 kV/mm IEC 60243-1
Relative Permittivity,1 MHz 2.7 - IEC 60250
Dissipation Factor,50/60 Hz 0.004 - IEC 60250
Dissipation Factor,1 MHz 0.008 - IEC 60250
Relative Permittivity,50/60 Hz 2.8 - IEC 60250
FLAME CHARACTERISTICS Value Unit Standard
UL Recognized,94HB Flame Class Rating(3) 0.71 mm UL 94
UL Recognized,94V-1 Flame Class Rating(3) 1.21 mm UL 94
UL Recognized,94V-0 Flame Class Rating(3) 1.47 mm UL 94
UL Recognized,94-5VA Rating(3) 3.4 mm UL 94
UL Recognized,94-5VB Rating(3) 2 mm UL 94
Source GMD,last updated:2000/01/05
Parameter Injection Molding Value Unit
Drying Temperature 80-90
Drying Time 3-4 hrs
Drying Time(Cumulative) 8 hrs
Maximum Moisture Content 0.04 %
Melt Temperature 245-275
Nozzle Temperature 245-275
Front-Zone 3 Temperature 245-275
Middle-Zone 2 Temperature 220-275
Rear-Zone 1 Temperature 220-255
Mold Temperature 60-80
Back Pressure 0.3-0.7 MPa
Screw Speed 40-70 rpm
Shot to Cylinder Size 30-80 %
Vent Depth 0.038-0.076 mm
Source GMD,last updated:2000/01/05

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics

1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

关健字:【Cycoloy* Resin PC/ABS C6200】