旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PC DX98550H 聚碳酸酯化合物,医疗级PC
  • 产 品:PC DX98550H 聚碳酸酯化合物,医疗级PC
  • 产 地:美国液氮
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

LNP* Colorcomp* Compound
LNP Colorcomp All Series
LNP* Colorcomp* resins contain colorants and special effects for a dazzling spectrum of colored materials. Among the offerings are opaque, translucent, and transparent resins, plus special effects, including edge glow, sparkle, glow, pearlescent, and thermochromic. LNP specialty compound offerings are available in a broad portfolio of standard and engineering materials.

LNP™Colorcomp™ Compound PC DX98550H 数据
Also known as:LNP™Colorcomp™Compound PDX-D-98550 LE
Product reorder name:DX98550H
LNP* Colorcomp* DX98550H is a compound based on Polycarbonate with Proprietary FIllers. Characteristics of this grade are Low Extractable, Healthcare.

MECHANICAL Value Unit Standard
Tensile Stress,yld,Type I,5mm/min 660 kgf/cm² ASTM D 638
Tensile Stress,brk,Type I,5mm/min 610 kgf/cm² ASTM D 638
Tensile Strain,brk,Type I,5mm/min 120 % ASTM D 638
Tensile Modulus,5mm/min 24600 kgf/cm² ASTM D 638
Flexural Stress 870 kgf/cm² ASTM D 790
Flexural Modulus,1.3mm/min,50mm span 23900 kgf/cm² ASTM D 790
THERMAL Value Unit Standard
CTE,-40℃ to 40℃,flow 3.30E-05 1/℃ ASTM E 831
CTE,-40℃ to 40℃,xflow 3.30E-05 1/℃ ASTM E 831
PHYSICAL Value Unit Standard
Specific Gravity 1.2 - ASTM D 792
Mold Shrinkage,flow,24 hrs(5) 0.6-0.8 % ASTM D 955
Mold Shrinkage,xflow,24 hrs(5) 0.6-0.8 % ASTM D 955
ELECTRICAL Value Unit Standard
Volume Resistivity 1.00E+16 Ohm-cm ASTM D 257
Surface Resistivity 1.00E+16 Ohm ASTM D 257
Dissipation Factor,1 MHz 0.01 - ASTM D 150
Source GMD,last updated:2011/05/06
Parameter Injection Molding Value Unit
Drying Temperature 120
Drying Time 4 hrs
Maximum Moisture Content 0.02 %
Melt Temperature 300-315
Front-Zone 3 Temperature 310-320
Middle-Zone 2 Temperature 305-315
Rear-Zone 1 Temperature 295-305
Mold Temperature 80-110
Back Pressure 0.2-0.3 MPa
Screw Speed 30-60 rpm
Source GMD,last updated:2011/05/06

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
 Buy SABIC Innovative please contact xiang zhang Engineering plastics

1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.PC/ABS FR3050 阻燃级,高耐热,耐化学改进
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

关健字:【LNP™Colorcomp™ Compound PC DX98550H