快速查找
主营塑料
产品推荐
- ⊕PPS OL003A 含玻璃纤维,聚四氟乙
- ⊕PBT 420SE0 玻纤30%增强,阻燃级
- ⊕PBT 310SE0 非增强型,PBT阻燃树脂
- ⊕PP HJ730 高流动,高钢性,高耐热
- ⊕PP FB71U6 耐热级,抗UV,阻燃级
- ⊕PA6 73G30L NC010 玻璃纤维30%增
- ⊕PA66 70G43L NC010 玻璃纤维43%增
- ⊕PA66 70G33L NC010 玻璃纤维33%增
- ⊕PA66 70G30L NC010 玻璃纤维30%增
- ⊕PA66 80G33L NC010 玻纤33%增强,
- ⊕PA66 FR50 NC010A 玻纤25%增强,阻
- ⊕POM 900P NC010 低粘度,热稳定,低
- ⊕POM 500P NC010 中高粘,热稳定,低
- ⊕POM 100P NC010 高粘度,韧性好,热
- ⊕PBT SK605 NC010 玻璃纤维30%增强
- ⊕PA66 1300G 玻纤增强级
联系我们
Lexan* Visualfx* Resin
Beauty Is More Than Skin Deep
Lexan Polycarbonate Visualfx Resins provide molded-in effects that can eliminate the need for modifications after molding. This can provide cleaner and more vibrant part aesthetics that will last as long as the part lasts. Visualfx Resins include Diamond, Luminescent, Diffusion, Lustre, and Edge Glow, as well as several metallic and natural material effects. Available in a variety of colors and base resins.
Lexan* Resin FXD121R 英文数据物性表
Transparent/translucent PC for light diffusion special effects. MFR of 18.2. Color package may affect performance.
Property
TYPICAL PROPERTIES (1)
MECHANICAL | Value | Unit | Standard |
Tensile Stress,yld,Type I,50mm/min | 620 | kgf/cm² | ASTM D 638 |
Tensile Stress,brk,Type I,50mm/min | 660 | kgf/cm² | ASTM D 638 |
Tensile Strain,yld,Type I,50mm/min | 6.2 | % | ASTM D 638 |
Tensile Strain,brk,Type I,50mm/min | 125 | % | ASTM D 638 |
Tensile Modulus,50mm/min | 24400 | kgf/cm² | ASTM D 638 |
Flexural Stress,yld,1.3mm/min,50mm span | 940 | kgf/cm² | ASTM D 790 |
Flexural Modulus,1.3mm/min,50mm span | 24200 | kgf/cm² | ASTM D 790 |
IMPACT | Value | Unit | Standard |
Izod Impact,notched,23℃ | 76 | cm-kgf/cm | ASTM D 256 |
Instrumented Impact Total Energy,23℃ | 737 | cm-kgf | ASTM D 3763 |
Instrumented Impact Total Energy,-30℃ | 777 | cm-kgf | ASTM D 3763 |
THERMAL | Value | Unit | Standard |
HDT,0.45 MPa,3.2mm,unannealed | 135 | ℃ | ASTM D 648 |
HDT,1.82 MPa,3.2mm,unannealed | 123 | ℃ | ASTM D 648 |
Relative Temp Index,Elec | 130 | ℃ | UL 746B |
Relative Temp Index,Mechw/impact | 130 | ℃ | UL 746B |
Relative Temp Index,Mech w/o impact | 130 | ℃ | UL 746B |
PHYSICAL | Value | Unit | Standard |
Specific Gravity | 1.19 | - | ASTM D 792 |
Water Absorption,24 hours | 0.13 | % | ASTM D 570 |
Mold Shrinkage,flow,3.2mm (5) | 0.5-0.7 | % | SABIC Method |
Melt Flow Rate,300℃/1.2 kgf | 18.2 | g/10 min | ASTM D 1238 |
ELECTRICAL | Value | Unit | Standard |
Hot Wire Ignition {PLC) | 2 | PLC Code | UL 746A |
High Voltage Arc Track Rate {PLC} | 2 | PLC Code | UL 746A |
High Ampere Arc Ign,surface {PLC} | 1 | PLC Code | UL 746A |
Comparative Tracking Index (UL) {PLC} | 2 | PLC Code | UL 746A |
FLAME CHARACTERISTICS | Value | Unit | Standard |
UL Recognized,94HB Flame Class Rating (3) | 0.71 | mm | UL 94 |
UV-light,water exposure/immersion | F2 | - | UL 746C |
Source GMD,last updated:2000/09/11 |
Parameter Injection Molding | Value | Unit |
Drying Temperature | 120 | ℃ |
Drying Time | 3-4 | hrs |
Drying Time (Cumulative) | 48 | hrs |
Maximum Moisture Content | 0.02 | % |
Melt Temperature | 280-305 | ℃ |
Nozzle Temperature | 275-300 | ℃ |
Front-Zone 3 Temperature | 280-305 | ℃ |
Middle-Zone 2 Temperature | 270-295 | ℃ |
Rear-Zone 1 Temperature | 260-280 | ℃ |
Mold Temperature | 70-95 | ℃ |
Back Pressure | 0.3-0.7 | MPa |
Screw Speed | 40-70 | rpm |
Shot to Cylinder Size | 40-60 | % |
Vent Depth | 0.025-0.076 | mm |
Source GMD,last updated:2000/09/11 |
THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.
1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
代理沙伯基础创新塑料(PC)聚碳酸酯材料
湘樟工程塑料©版权所有