旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PC 503R 冲击强度优异,阻燃级,UV稳定,内部脱模
  • 产 品:PC 503R 冲击强度优异,阻燃级,UV稳定,内部脱模
  • 产 地:沙伯基础创新
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

Lexan* General Purpose Filled Resin
General Purpose Grades
General purpose filled materials offer excellent rigidity and superior impact strength along with highly stable mechanical and electrical properties. They are available in different viscosity levels; some grades have easy release characteristics.

Lexan* Resin 503R 数据
10% GR PC. Optimum combination of high modulus plus excellent impact strength and flame retardance. UV-stabilized. Internal mold release.

Property
TYPICAL PROPERTIES (1)

MECHANICAL Value Unit Standard
Tensile Stress,yld,Type I,5 mm/min 670 kgf/cm² ASTM D 638
Tensile Stress,brk,Type I,5 mm/min 560 kgf/cm² ASTM D 638
Tensile Strain,yld,Type I,5 mm/min 8 % ASTM D 638
Tensile Strain,brk,Type I,5 mm/min 15 % ASTM D 638
Flexural Stress,yld,1.3 mm/min,50 mm span 1050 kgf/cm² ASTM D 790
Flexural Modulus,1.3 mm/min,50 mm span 35100 kgf/cm² ASTM D 790
Hardness,Rockwell M 85 - ASTM D 785
Hardness,Rockwell R 124 - ASTM D 785
Taber Abrasion,CS-17,1 kg 11 mg/1000cy ASTM D 1044
IMPACT Value Unit Standard
Izod Impact,unnotched,23℃ 217 cm-kgf/cm ASTM D 4812
Izod Impact,notched,23℃ 10 cm-kgf/cm ASTM D 256
Tensile Impact,Type S 160 cm-kgf/cm² ASTM D 1822
Falling Dart Impact(D 3029),23℃ 1036 cm-kgf ASTM D 3029
THERMAL Value Unit Standard
Vicat Softening Temp,Rate B/50 154 ASTM D 1525
HDT,0.45 MPa,6.4 mm,unannealed 146 ASTM D 648
HDT,1.82 MPa,6.4 mm,unannealed 142 ASTM D 648
CTE,-40℃ to 95℃,flow 3.24E-05 1/℃ ASTM E 831
Specific Heat 1.21 J/g-℃ ASTM C 351
Thermal Conductivity 0.2 W/m-℃ ASTM C 177
Relative Temp Index,Elec 120 UL 746B
Relative Temp Index,Mech w/impact 110 UL 746B
Relative Temp Index,Mech w/o impact 125 UL 746B
PHYSICAL Value Unit Standard
Specific Gravity 1.25 - ASTM D 792
Specific Volume 0.8 cm³/g ASTM D 792
Density 1.245 g/cm³ ASTM D 792
Water Absorption,24 hours 0.12 % ASTM D 570
Water Absorption,equilibrium,23C 0.31 % ASTM D 570
Mold Shrinkage,flow,3.2 mm(5) 0.2-0.4 % SABIC Method
ELECTRICAL Value Unit Standard
Volume Resistivity >1.E+17 Ohm-cm ASTM D 257
Dielectric Strength,in air,3.2 mm 17.7 kV/mm ASTM D 149
Relative Permittivity,50/60 Hz 3.1 - ASTM D 150
Relative Permittivity,1 MHz 3.05 - ASTM D 150
Dissipation Factor,50/60 Hz 0.0008 - ASTM D 150
Dissipation Factor,1 MHz 0.0075 - ASTM D 150
Arc Resistance,Tungsten{PLC} 7 PLC Code ASTM D 495
Hot Wire Ignition{PLC) 1 PLC Code UL 746A
High Voltage Arc Track Rate{PLC} 3 PLC Code UL 746A
High Ampere Arc Ign,surface{PLC} 1 PLC Code UL 746A
Comparative Tracking Index(UL){PLC} 4 PLC Code UL 746A
FLAME CHARACTERISTICS Value Unit Standard
UL Recognized,94V-0 Flame Class Rating(3) 1.52 mm UL 94
UL Recognized,94-5VA Rating(3) 2.99 mm UL 94
Oxygen Index(LOI) 36 % ASTM D 2863
UV-light,water exposure/immersion F1 - UL 746C
Source GMD,last updated:1999/12/29
Parameter Injection Molding Value Unit
Drying Temperature 120
Drying Time 3-4 hrs
Drying Time(Cumulative) 48 hrs
Maximum Moisture Content 0.02 %
Melt Temperature 310-330
Nozzle Temperature 305-325
Front-Zone 3 Temperature 310-330
Middle-Zone 2 Temperature 300-320
Rear-Zone 1 Temperature 290-310
Mold Temperature 80-115
Back Pressure 0.3-0.7 MPa
Screw Speed 40-70 rpm
Shot to Cylinder Size 40-60 %
Vent Depth 0.025-0.076 mm
Source GMD,last updated:1999/12/29
• NOTE: Back Pressure, Screw Speed, Shot to Cylinder Size and Vent Depth are only mentioned as general guidelines. These may not apply or need adjustment in specific situations such as low shot sizes, thin wall molding and gas-assist molding.

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.

1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
代理沙伯基础创新塑料(PC)聚碳酸酯材料http://www.pa66-suliao.com/product/resu/CPE/