PC 8345 玻璃纤维35增强,高粘度,易释放

快速查找

主营塑料

更多>>

产品推荐

联系我们

塑胶原料报价

产品：PC 8345 玻璃纤维35增强,高粘度,易释放
产地：Bayer 拜耳
价格：电话报价
库存：20吨
交货：江苏苏州
苏州希普能：185 5121 3137 谭经理

上一篇：PC 8325 玻璃纤维20增强,高粘度,易释放下一篇：PC 9125 玻纤20增强,氯和溴阻燃,中粘度,易释放

[Datasheet Makrolon 8345]数据
MVR (300 °C/1.2 kg) 3.0 cm³/10 min; 35 % glass fiber reinforced; high viscosity; easy release

☆These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350.
Impact properties: N = non-break, P = partial break, C = complete break

ISO Shortname:ISO 7391-PC,GR,(,,)-05-3,GF35
Property		Test Condition	Unit	Standard	Value
Rheological properties
☆	Melt volume-flow rate	300℃;1.2 kg	cm³/10 min	ISO 1133	3
.	Molding shrinkage,parallel/normal	值的范围一般实践经验的基础上	%	b.o.ISO 2577	0.3 - 0.5
.	Melt mass-flow rate	300℃;1.2 kg	g/10 min	ISO 1133	3.5
Mechanical properties(23℃/50 % r.h.)
☆	Tensile modulus	1 mm/min	MPa	ISO 527-1,-2	9400
☆	Yield stress	50 mm/min	MPa	ISO 527-1,-2	113
☆	Yield strain	50 mm/min	%	ISO 527-1,-2	1.9
☆	Stress at break	5 mm/min	MPa	ISO 527-1,-2	110
☆	Strain at break	5 mm/min	%	ISO 527-1,-2	1.8
☆	Tensile creep modulus	1 h	MPa	ISO 899-1	9000
☆	Tensile creep modulus	1000 h	MPa	ISO 899-1	8500
.	Flexural modulus	2 mm/min	MPa	ISO 178	8600
.	Flexural strength	2 mm/min	MPa	ISO 178	170
.	Flexural strain at flexural strength	2 mm/min	%	ISO 178	2.5
☆	Charpy impact strength	23℃	kJ/m²	ISO 179-1eU	40C
☆	Charpy impact strength	-30℃	kJ/m²	ISO 179-1eU	45C
.	Charpy notched impact strength	23℃;3 mm	kJ/m²	ISO 7391/b.o.ISO 179-1eA	8C
.	Izod notched impact strength	23℃;3.2 mm	kJ/m²	b.o.ISO 180-A	8C
☆	Puncture maximum force	23℃	N	ISO 6603-2	900
☆	Puncture maximum force	-30℃	N	ISO 6603-2	900
☆	Puncture energy	23℃	J	ISO 6603-2	5
☆	Puncture energy	-30℃	J	ISO 6603-2	5
.	Ball indentation hardness	.	N/mm²	ISO 2039-1	175
Thermal properties
☆	Temperature of deflection under load	1.80 MPa	℃	ISO 75-1,-2	140
☆	Temperature of deflection under load	0.45 MPa	℃	ISO 75-1,-2	144
☆	Vicat softening temperature	50 N;50℃/h	℃	ISO 306	148
.	Vicat softening temperature	50 N;120℃/h	℃	ISO 306	149
☆	线性热膨胀系数,并行	23 to 55℃	10-4/K	ISO 11359-1,-2	0.2
☆	横向线性热膨胀系数	23 to 55℃	10-4/K	ISO 11359-1,-2	0.6
☆	燃烧性能UL94(1.5毫米)[UL认可]	1.5 mm	Class	UL 94	V-1
☆	燃烧性UL94 [UL认可]	3.0 mm	Class	UL 94	V-0
☆	Oxygen index	Method A	%	ISO 4589-2	35
.	Thermal conductivity	23℃	W/(m·K)	ISO 8302	0.24
.	耐热(球压试验)	.	℃	IEC 60695-10-2	136
.	相对温度指数(拉伸强度)[UL认可]	1.5 mm	℃	UL 746B	125
.	相对温度指数(拉伸冲击强度)[UL认可]	1.5 mm	℃	UL 746B	115
.	相对温度指数(介电强度)[UL认可]	1.5 mm	℃	UL 746B	125
.	Glow wire test(GWFI)	1.5 mm	℃	IEC 60695-2-12	960
.	Glow wire test(GWFI)	3.0 mm	℃	IEC 60695-2-12	960
.	来自小燃烧器的火焰中的应用	Method K and F;2.0 mm	Class	DIN 53438-1,-3	K1,F1
.	Needle flame test	Method K;1.5 mm	s	IEC 60695-11-5	60
.	Needle flame test	Method K;2.0 mm	s	IEC 60695-11-5	60
.	Needle flame test	Method K;3.0 mm	s	IEC 60695-11-5	120
.	Needle flame test	Method F;1.5 mm	s	IEC 60695-11-5	120
.	Needle flame test	Method F;2.0 mm	s	IEC 60695-11-5	120
.	Needle flame test	Method F;3.0 mm	s	IEC 60695-11-5	120
.	Burning rate(US-FMVSS)	>=1.0 mm	mm/min	ISO 3795	passed
.	Flash ignition temperature	.	℃	ASTM D1929	470
.	Self ignition temperature	.	℃	ASTM D1929	550
Electrical properties(23℃/50 % r.h.)
☆	Relative permittivity	100 Hz	-	IEC 60250	3.6
☆	Relative permittivity	1 MHz	-	IEC 60250	3.6
☆	Dissipation factor	100 Hz	10-4	IEC 60250	10
☆	Dissipation factor	1 MHz	10-4	IEC 60250	90
☆	Volume resistivity	.	Ohm·m	IEC 60093	1E14
☆	Surface resistivity	.	Ohm	IEC 60093	1E16
☆	Electrical strength	1 mm	kV/mm	IEC 60243-1	36
☆	Comparative tracking index CTI	Solution A	Rating	IEC 60112	175
.	Comparative tracking index CTI M	Solution B	Rating	IEC 60112	125M
.	Electrolytic corrosion	.	Rating	IEC 60426	A1
Other properties(23℃)
☆	Water absorption(saturation value)	Water at 23℃	%	ISO 62	0.20
☆	Water absorption(equilibrium value)	23℃;50 % r.h.	%	ISO 62	0.10
☆	Density	.	kg/m³	ISO 1183-1	1480
.	Glass fiber content	Method A	%	b.o.ISO 3451-1	35
.	Bulk density	Pellets	kg/m³	ISO 60	670
Processing conditions for test specimens
☆	Injection molding-Melt temperature	.	℃	ISO 294	300
☆	Injection molding-Mold temperature	.	℃	ISO 294	110
☆	Injection molding-Injection velocity	.	mm/s	ISO 294	200

塑料种类

快速查找

主营塑料

产品推荐

联系我们