PC 6487 阻燃,中等粘度,紫外线稳定,易于释放

快速查找

主营塑料

更多>>

产品推荐

联系我们

塑胶原料报价

产品：PC 6487 阻燃,中等粘度,紫外线稳定,易于释放
产地：Bayer 拜耳
价格：电话报价
库存：20吨
交货：江苏苏州
苏州希普能：185 5121 3137 谭经理

上一篇：PC 6485 阻燃防火,中等粘度,易释放下一篇：PC 6555 氯和无溴阻燃,中等粘度,易释放

[Datasheet Makrolon 6487]数据
MVR (300 °C/1.2 kg) 9.0 cm³/10 min; flame retardant; UL 94V-0/1.5 mm and 5VA/3.0 mm; medium viscosity; UV stabilized; easy release

☆These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350.
Impact properties: N = non-break, P = partial break, C = complete break

ISO Shortname:ISO 7391-PC,MFLR,(,,)-09-9
Property		Test Condition	Unit	Standard	Value
Rheological properties
☆	Melt volume-flow rate	300℃;1.2 kg	cm³/10 min	ISO 1133	9
☆	Molding shrinkage,parallel	60x60x2 mm;500 bar	%	ISO 294-4	0.7
☆	Molding shrinkage,normal	60x60x2 mm;500 bar	%	ISO 294-4	0.75
.	Molding shrinkage,parallel/normal	值的范围一般实践经验的基础上	%	b.o.ISO 2577	0.6-0.8
.	Melt mass-flow rate	300℃;1.2 kg	g/10 min	ISO 1133	10
Mechanical properties (23℃/50 %r. h.)
☆	Tensile modulus	1 mm/min	MPa	ISO 527-1,-2	2450
☆	Yield stress	50 mm/min	MPa	ISO 527-1,-2	66
☆	Yield strain	50 mm/min	%	ISO 527-1,-2	6
☆	Nominal strain at break	50 mm/min	%	ISO 527-1,-2	> 50
.	Stress at break	50 mm/min	MPa	ISO 527-1,-2	65
.	Strain at break	50 mm/min	%	b.o.ISO 527-1,-2	115
.	Flexural modulus	2 mm/min	MPa	ISO 178	2450
.	Flexural strength	2 mm/min	MPa	ISO 178	99
.	Flexural strain at flexural strength	2 mm/min	%	ISO 178	7
.	Flexural stress at 3.5 %strain	2 mm/min	MPa	ISO 178	75
☆	Charpy impact strength	23℃	kJ/m²	ISO 179-1eU	N
☆	Charpy impact strength	-30℃	kJ/m²	ISO 179-1eU	N
.	Charpy notched impact strength	23℃;3 mm	kJ/m²	ISO 7391/b.o.ISO 179-1eA	70P(C)
.	Charpy notched impact strength	-30℃;3 mm	kJ/m²	ISO 7391/b.o.ISO 179-1eA	12C
.	Izod notched impact strength	23℃;3 mm	kJ/m²	ISO 7391/b.o.ISO 180-A	70P(C)
.	Izod notched impact strength	-30℃;3 mm	kJ/m²	ISO 7391/b.o.ISO 180-A	12C
☆	Puncture maximum force	23℃	N	ISO 6603-2	5200
☆	Puncture maximum force	-30℃	N	ISO 6603-2	6000
☆	Puncture energy	23℃	J	ISO 6603-2	50
☆	Puncture energy	-30℃	J	ISO 6603-2	55
.	Ball indentation hardness	.	N/mm²	ISO 2039-1	117
Thermal properties
☆	Glass transition temperature	10℃/min	℃	ISO 11357-1,-2	141
☆	Temperature of deflection under load	1.80 MPa	℃	ISO 75-1,-2	122
☆	Temperature of deflection under load	0.45 MPa	℃	ISO 75-1,-2	134
☆	Vicat softening temperature	50 N;50℃/h	℃	ISO 306	143
.	Vicat softening temperature	50 N;120℃/h	℃	ISO 306	141
☆	线性热膨胀系数,并行	23 to 55℃	10-4/K	ISO 11359-1,-2	0.65
☆	横向线性热膨胀系数	23 to 55℃	10-4/K	ISO 11359-1,-2	0.65
☆	燃烧性能UL94(1.5毫米)[UL认可]	1.5 mm	Class	UL 94	V-0
☆	燃烧性能UL94-5V[UL认可]	3.0 mm	Class	UL 94	5VA
☆	Oxygen index	Method A	%	ISO 4589-2	36
.	Thermal conductivity	23℃	W/(m·K)	ISO 8302	0.20
.	耐热(球压试验)	.	℃	IEC 60695-10-2	135
.	相对温度指数(拉伸强度)[UL认可]	1.5 mm	℃	UL 746B	125
.	相对温度指数(拉伸冲击强度)[UL认可]	1.5 mm	℃	UL 746B	115
.	相对温度指数(介电强度)[UL认可]	1.5 mm	℃	UL 746B	125
.	Glow wire test(GWFI)	1.5 mm	℃	IEC 60695-2-12	960
.	Glow wire test(GWFI)	3.0 mm	℃	IEC 60695-2-12	960
.	Glow wire test(GWIT)	1.5 mm	℃	IEC 60695-2-13	900
.	Glow wire test(GWIT)	3.0 mm	℃	IEC 60695-2-13	930
.	来自小燃烧器的火焰中的应用	Method K and F;2.0 mm	Class	DIN 53438-1,-3	K1,F1
.	Burning rate(US-FMVSS)	>=1.0 mm	mm/min	ISO 3795	passed
.	Flash ignition temperature	.	℃	ASTM D1929	470
.	Self ignition temperature	.	℃	ASTM D1929	550
Electrical properties (23℃/50 %r. h.)
☆	Relative permittivity	100 Hz	-	IEC 60250	3.1
☆	Relative permittivity	1 MHz	-	IEC 60250	3.0
☆	Dissipation factor	100 Hz	10-4	IEC 60250	8
☆	Dissipation factor	1 MHz	10-4	IEC 60250	90
☆	Volume resistivity	.	Ohm·m	IEC 60093	1E14
☆	Surface resistivity	.	Ohm	IEC 60093	1E16
☆	Electrical strength	1 mm	kV/mm	IEC 60243-1	34
☆	Comparative tracking index CTI	Solution A	Rating	IEC 60112	225
.	Comparative tracking index CTI M	Solution B	Rating	IEC 60112	125M
.	Electrolytic corrosion	.	Rating	IEC 60426	A1
Other properties (23℃)
☆	Water absorption(saturation value)	Water at 23℃	%	ISO 62	0.30
☆	Water absorption(equilibrium value)	23℃;50 %r.h.	%	ISO 62	0.12
☆	Density	.	kg/m³	ISO 1183-1	1200
.	Bulk density	Pellets	kg/m³	ISO 60	640
Processing conditions for test specimens
☆	Injection molding-Melt temperature	.	℃	ISO 294	300
☆	Injection molding-Mold temperature	.	℃	ISO 294	80
☆	Injection molding-Injection velocity	.	mm/s	ISO 294	200

塑料种类

快速查找

主营塑料

产品推荐

联系我们