旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PC 6267 X 氯和溴阻燃,低粘度,紫外线稳定,易释放
  • 产 品:PC 6267 X 氯和溴阻燃,低粘度,紫外线稳定,易释放
  • 产 地:Bayer 拜耳
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

[Datasheet Makrolon 6267 X]数据
MVR (300 °C/1.2 kg) 19 cm³/10 min; chlorine- and bromine-free flame retardancy; UL 94V-0/1.5 mm; low viscosity; UV stabilized; easy release

☆These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350.
Impact properties: N = non-break, P = partial break, C = complete break

ISO Shortname:ISO 7391-PC,MFLR,(,,)-18-9
Property Test Condition Unit Standard Value
Rheological properties
Melt volume-flow rate 300℃;1.2 kg cm³/10 min ISO 1133 19
Molding shrinkage,parallel 60x60x2 mm;500 bar % ISO 294-4 0.65
Molding shrinkage,normal 60x60x2 mm;500 bar % ISO 294-4 0.65
. Molding shrinkage,parallel/normal 值的范围一般实践经验的基础上 % b.o.ISO 2577 0.5 - 0.7
. Melt mass-flow rate 300℃;1.2 kg g/10 min ISO 1133 20
Mechanical properties(23℃/50 % r.h.)
Tensile modulus 1 mm/min MPa ISO 527-1,-2 2450
Yield stress 50 mm/min MPa ISO 527-1,-2 67
Yield strain 50 mm/min % ISO 527-1,-2 6
Nominal strain at break 50 mm/min % ISO 527-1,-2 > 50
. Stress at break 50 mm/min MPa ISO 527-1,-2 65
. Strain at break 50 mm/min % b.o.ISO 527-1,-2 120
. Flexural modulus 2 mm/min MPa ISO 178 2400
. Flexural strength 2 mm/min MPa ISO 178 97
. Flexural strain at flexural strength 2 mm/min % ISO 178 6.9
. Flexural stress at 3.5 % strain 2 mm/min MPa ISO 178 74
Charpy impact strength 23℃ kJ/m² ISO 179-1eU N
Charpy impact strength -30℃ kJ/m² ISO 179-1eU N
. Charpy notched impact strength 23℃;3 mm kJ/m² ISO 7391/b.o.ISO 179-1eA 12C(P)
. Charpy notched impact strength -30℃;3 mm kJ/m² ISO 7391/b.o.ISO 179-1eA 12C
. Izod notched impact strength 23℃;3.2 mm kJ/m² b.o.ISO 180-A 12C(P)
. Izod notched impact strength -30℃;3.2 mm kJ/m² b.o.ISO 180-A 12C
Puncture maximum force 23℃ N ISO 6603-2 5000
Puncture maximum force -30℃ N ISO 6603-2 5900
Puncture energy 23℃ J ISO 6603-2 50
Puncture energy -30℃ J ISO 6603-2 55
. Ball indentation hardness . N/mm² ISO 2039-1 116
Thermal properties
Temperature of deflection under load 1.80 MPa ISO 75-1,-2 122
Temperature of deflection under load 0.45 MPa ISO 75-1,-2 134
Vicat softening temperature 50 N;50℃/h ISO 306 144
. Vicat softening temperature 50 N;120℃/h ISO 306 145
线性热膨胀系数,并行 23 to 55℃ 10-4/K ISO 11359-1,-2 0.65
横向线性热膨胀系数 23 to 55℃ 10-4/K ISO 11359-1,-2 0.65
燃烧性能UL94(1.5毫米)[UL认可] 1.5 mm Class UL 94 V-0
Oxygen index Method A % ISO 4589-2 36
. Thermal conductivity 23℃ W/(m·K) ISO 8302 0.2
. 耐热(球压试验) . IEC 60695-10-2 135
. 相对温度指数(拉伸强度)[UL认可] 1.5 mm UL 746B 125
. 相对温度指数(拉伸冲击强度)[UL认可] 1.5 mm UL 746B 115
. 相对温度指数(介电强度)[UL认可] 1.5 mm UL 746B 125
. Glow wire test(GWFI) 0.75 mm IEC 60695-2-12 960
. Glow wire test(GWFI) 1.5 mm IEC 60695-2-12 960
. Glow wire test(GWFI) 3.0 mm IEC 60695-2-12 960
. 来自小燃烧器的火焰中的应用 Method K and F;2.0 mm Class DIN 53438-1,-3 K1,F1
. Needle flame test Method K;1.5 mm s IEC 60695-11-5 120
. Needle flame test Method K;2.0 mm s IEC 60695-11-5 120
. Needle flame test Method K;3.0 mm s IEC 60695-11-5 120
. Needle flame test Method F;1.5 mm s IEC 60695-11-5 120
. Needle flame test Method F;2.0 mm s IEC 60695-11-5 120
. Needle flame test Method F;3.0 mm s IEC 60695-11-5 120
. Burning rate(US-FMVSS) >=1.0 mm mm/min ISO 3795 passed
. Flash ignition temperature . ASTM D1929 460
. Self ignition temperature . ASTM D1929 530
Electrical properties(23℃/50 % r.h.)
Relative permittivity 100 Hz - IEC 60250 3.1
Relative permittivity 1 MHz - IEC 60250 3
Dissipation factor 100 Hz 10月4日 IEC 60250 8
Dissipation factor 1 MHz 10月4日 IEC 60250 90
Volume resistivity . Ohm·m IEC 60093 1.00E+14
Surface resistivity . Ohm IEC 60093 1.00E+16
Electrical strength 1 mm kV/mm IEC 60243-1 34
Comparative tracking index CTI Solution A Rating IEC 60112 225
. Comparative tracking index CTI M Solution B Rating IEC 60112 125M
. Electrolytic corrosion . Rating IEC 60426 A1
Other properties(23℃)
Water absorption(saturation value) Water at 23℃ % ISO 62 0.3
Water absorption(equilibrium value) 23℃;50 % r.h. % ISO 62 0.12
Density . kg/m³ ISO 1183-1 1200
. Bulk density Pellets kg/m³ ISO 60 640
Processing conditions for test specimens
Injection molding-Melt temperature . ISO 294 280
Injection molding-Mold temperature . ISO 294 80
Injection molding-Injection velocity . mm/s ISO 294 200