旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PBT IQNH2900 无卤阻燃,PBT+PC合金,抗冲击改性
  • 产 品:PBT IQNH2900 无卤阻燃,PBT+PC合金,抗冲击改性
  • 产 地:沙伯基础创新
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

Xenoy* Resin
Xenoy* Resin All Series
Xenoy* alloys are a blend of semi-crystalline polyester (typically polybutylene terephthalate, PBT, or polyethylene terephthalate, PET) and polycarbonate (PC). The Xenoy family offers good chemical resistance, great impact resistance and toughness even at low temperatures, heat resistance, and outstanding aesthetic and flow characteristics.

XENOY™ Resin PBT+PC IQNH2900 数据表
Import Grade. UL94 V-0 Performance with Non-Brominated Flame Retardant. PCR% is up to 12% by using Valox iQ* resin.

Property
TYPICAL PROPERTIES (1)

MECHANICAL Value Unit Standard
Tensile Stress,yld,Type I,50mm/min 640 kgf/cm² ASTM D 638
Tensile Stress,brk,Type I,50mm/min 420 kgf/cm² ASTM D 638
Tensile Strain,yld,Type I,50mm/min 4 % ASTM D 638
Tensile Strain,brk,Type I,50mm/min 65 % ASTM D 638
Tensile Modulus,50mm/min 25200 kgf/cm² ASTM D 638
Flexural Stress,yld,1.3mm/min,50mm span 900 kgf/cm² ASTM D 790
Flexural Modulus,1.3mm/min,50mm span 22800 kgf/cm² ASTM D 790
IMPACT Value Unit Standard
Izod Impact,notched,23℃ 56 cm-kgf/cm ASTM D 256
Instrumented Impact Total Energy,23℃ 662 cm-kgf ASTM D 3763
THERMAL Value Unit Standard
Vicat Softening Temp,Rate B/50 100 ASTM D 1525
HDT,1.82 MPa,3.2mm,unannealed 77 ASTM D 648
PHYSICAL Value Unit Standard
Specific Gravity 1.2 - ASTM D 792
Mold Shrinkage,flow,3.2mm(5) 0.5-0.7 % SABIC Method
Melt Flow Rate,266℃/5.0 kgf 26 g/10 min ASTM D 1238
FLAME CHARACTERISTICS Value Unit Standard
UL Recognized,94V-1 Flame Class Rating(3) 1.1 mm UL 94
UL Recognized,94V-0 Flame Class Rating(3) 1.5 mm UL 94
UL Recognized,94-5VB Rating(3) 2.5 mm UL 94
Source GMD,last updated:2011/04/22
Parameter Injection Molding Value Unit
Drying Temperature 80-90
Drying Time 3-4 hrs
Drying Time(Cumulative) 8 hrs
Maximum Moisture Content 0.04 %
Melt Temperature 245-275
Nozzle Temperature 245-275
Front-Zone 3 Temperature 245-275
Middle-Zone 2 Temperature 220-265
Rear-Zone 1 Temperature 220-255
Mold Temperature 60-80
Back Pressure 0.3-0.7 MPa
Screw Speed 40-70 rpm
Shot to Cylinder Size 30-80 %
Vent Depth 0.038-0.076 mm
Source GMD,last updated:2011/04/22

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics

1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.HDPE 8003H 中空吹制级
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

关健字:【XENOY™ Resin PBT+PC IQNH2900