旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PBT K4530 玻纤15%增强PBT,水解稳定,高流动
  • 产 品:PBT K4530 玻纤15%增强PBT,水解稳定,高流动
  • 产 地:沙伯基础创新
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

Valox* Resin
Valox* Resin All Series
The Valox* family of thermoplastic polyester resins are semi-crystalline materials based on polybutylene terephthalate (PBT) and/or polyethylene terephthalate (PET) polymers. Valox resins are highly tailorable, combining heat, chemical resistance, and outstanding electrical properties with exceptionally good processability and surface appearance.

Valox* Resin PBT K4530 数据表
15% glass reinforced PBT, Hydrolytically stable, High flow, Automotive connectors.

Property
TYPICAL PROPERTIES (1)

MECHANICAL Value Unit Standard
Tensile Stress,yld,Type I,5mm/min 1050 kgf/cm² ASTM D 638
Tensile Stress,brk,Type I,5mm/min 1050 kgf/cm² ASTM D 638
Tensile Strain,yld,Type I,5mm/min 4 % ASTM D 638
Tensile Strain,brk,Type I,5mm/min 4 % ASTM D 638
Tensile Modulus,5mm/min 36200 kgf/cm² ASTM D 638
Flexural Stress,brk,1.3mm/min,50mm span 1520 kgf/cm² ASTM D 790
Flexural Modulus,1.3mm/min,50mm span 47300 kgf/cm² ASTM D 790
IMPACT Value Unit Standard
Izod Impact,unnotched,23℃ 40 cm-kgf/cm ASTM D 4812
Izod Impact,notched,23℃ 5 cm-kgf/cm ASTM D 256
THERMAL Value Unit Standard
HDT,0.45 MPa,3.2mm,unannealed 218 ASTM D 648
HDT,1.82 MPa,3.2mm,unannealed 193 ASTM D 648
PHYSICAL Value Unit Standard
Specific Gravity 1.41 - ASTM D 792
Mold Shrinkage,flow,3.2mm(5) 0.7-0.9 % SABIC Method
Mold Shrinkage,xflow,3.2mm(5) 1-1.2 % SABIC Method
AFTER 40 CYCLES,SIMILAR TO USCAR-2,CLASS III Value Unit Standard
Tensile Stress,brk,Type I,5mm/min 830 kgf/cm² ASTM D 638
Tensile Strain,brk,Type I,5mm/min 2.5 % ASTM D 638
Flexural Modulus,1.3mm/min,50mm span 46100 kgf/cm² ASTM D 790
Flexural Strain,1.3mm/min,50mm span 9.7 % ASTM D 790
Instrumented Impact,Total Energy,23℃ 60 cm-kgf ASTM D 3763
PROPERTIES AFTER 1008 HOURS AT 125?C Value Unit Standard
Tensile Stress,brk,Type I,5mm/min 990 kgf/cm² ASTM D 638
Tensile Strain,brk,Type I,5mm/min 4 % ASTM D 638
Flexural Modulus,1.3mm/min,50mm span 49100 kgf/cm² ASTM D 790
Flexural Strain,1.3mm/min,50mm span 7 % ASTM D 790
Instrumented Impact,Total Energy,23℃ 50 cm-kgf ASTM D 3763
AFTER 40 CYCLES,SIMILAR TO USCAR-2,CLASS IV Value Unit Standard
Tensile Stress,brk,Type I,5mm/min 910 kgf/cm² ASTM D 638
Tensile Strain,brk,Type I,5mm/min 2.3 % ASTM D 638
Flexural Modulus,1.3mm/min,50mm span 52000 kgf/cm² ASTM D 790
Flexural Strain,1.3mm/min,50mm span 6 % ASTM D 790
Instrumented Impact,Total Energy,23℃ 50 cm-kgf ASTM D 3763
PROPERTIES AFTER 1008 HOURS AT 155?C Value Unit Standard
Tensile Stress,brk,Type I,5mm/min 49070 kgf/cm² ASTM D 638
Tensile Strain,yld,Type I,5mm/min 97.2 % ASTM D 638
Flexural Modulus,1.3mm/min,50mm span 0 kgf/cm² ASTM D 790
Flexural Strain,1.3mm/min,50mm span 3.8 % ASTM D 790
Source GMD,last updated:2012/05/01

• We cannot overemphasize -- OVERDRYING SHOULD BE AVOIDED. Use a dehumidifying desiccant bed dryer with -30℃ (-20℉) dew point air (approximately 1 cfm/lb/hr air flow). Exceeding the temperature or time recommended can compromise the hydrolysis performance of the material or the drying equipment can be damaged.

Parameter Injection Molding Value Unit
Drying Temperature 60-75
Drying Time 4-6 hrs
Drying Time(Cumulative) 8 hrs
Maximum Moisture Content 0.05 %
Melt Temperature 250-265
Nozzle Temperature 245-260
Front-Zone 3 Temperature 250-265
Middle-Zone 2 Temperature 245-260
Rear-Zone 1 Temperature 240-255
Mold Temperature 65-90
Back Pressure 0.3-0.7 MPa
Screw Speed 50-80 rpm
Shot to Cylinder Size 40-80 %
Vent Depth 0.025-0.038 mm
Source GMD,last updated:2012/05/01

• If material is stored in dryer for extended periods (overnight or more):
Lower dryer temperature to room temperature.
Recirculate cool dry air over material.

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics

1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.PPO FN215X 发泡树脂,生产率改进
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

关健字:【Valox* Resin PBT K4530