旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PBT IQ420HP 玻纤30%加固,食品级PBT
  • 产 品:PBT IQ420HP 玻纤30%加固,食品级PBT
  • 产 地:沙伯基础创新
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

Valox* Resin
Valox* Resin All Series
The Valox* family of thermoplastic polyester resins are semi-crystalline materials based on polybutylene terephthalate (PBT) and/or polyethylene terephthalate (PET) polymers. Valox resins are highly tailorable, combining heat, chemical resistance, and outstanding electrical properties with exceptionally good processability and surface appearance.

Valox* Resin PBT IQ420HP 数据表
Environmentally responsible, low carbon footprint Valox iQ* resin - Valox* iQ420HP resin is made using iQ-PBT resin and 30% glass fiber reinforcement. Valox* iQ420HP may be used for the production of food contact articles intended for repeat use (and not for single use) in contact with all food types, and under all conditions of use per FDA table of food types, with the exception of irradiation and cooking/baking at temperatures above 250 degrees F. This includes microwaving within these same temperature constraints. If colorants are added to the resin, these must be evaluated separately for their appropriateness for food contact applications.

Property
TYPICAL PROPERTIES (1)

MECHANICAL Value Unit Standard
Tensile Stress,yld,Type I,5mm/min 1160 kgf/cm² ASTM D 638
Tensile Stress,brk,Type I,5mm/min 1160 kgf/cm² ASTM D 638
Tensile Strain,yld,Type I,5mm/min 2.2 % ASTM D 638
Tensile Strain,brk,Type I,5mm/min 2.2 % ASTM D 638
Tensile Modulus,5mm/min 120300 kgf/cm² ASTM D 638
Flexural Stress,yld,1.3mm/min,50mm span 2140 kgf/cm² ASTM D 790
Flexural Modulus,1.3mm/min,50mm span 92700 kgf/cm² ASTM D 790
Tensile Stress,yield,5mm/min 139 MPa ISO 527
Tensile Stress,break,5mm/min 139 MPa ISO 527
Tensile Strain,yield,5mm/min 1.6 % ISO 527
Tensile Strain,break,5mm/min 1.6 % ISO 527
Tensile Modulus,1mm/min 10700 MPa ISO 527
Flexural Stress,yield,2mm/min 210 MPa ISO 178
Flexural Modulus,2mm/min 9100 MPa ISO 178
IMPACT Value Unit Standard
Izod Impact,unnotched,23℃ 78 cm-kgf/cm ASTM D 4812
Izod Impact,notched,23℃ 8 cm-kgf/cm ASTM D 256
Izod Impact,notched,-30℃ 8 cm-kgf/cm ASTM D 256
Instrumented Impact Total Energy,23℃ 71 cm-kgf ASTM D 3763
Izod Impact,notched 80*10*4 +23℃ 8 kJ/m² ISO 180/1A
Izod Impact,notched 80*10*4 -30℃ 8 kJ/m² ISO 180/1A
Charpy 23℃,V-notch Edgew 80*10*4 sp=62mm 14 kJ/m² ISO 179/1eA
THERMAL Value Unit Standard
Vicat Softening Temp,Rate B/50 206 ASTM D 1525
HDT,1.82 MPa,3.2mm,unannealed 203 ASTM D 648
CTE,-40℃ to 40℃,flow 2.50E-05 1/℃ ASTM E 831
CTE,-40℃ to 40℃,xflow 8.90E-05 1/℃ ASTM E 831
CTE,-40℃ to 40℃,flow 2.50E-05 1/℃ ISO 11359-2
CTE,-40℃ to 40℃,xflow 8.90E-05 1/℃ ISO 11359-2
Ball Pressure Test,approximate maximum 200 IEC 60695-10-2
Vicat Softening Temp,Rate B/50 206 ISO 306
Vicat Softening Temp,Rate B/120 206 ISO 306
HDT/Af,1.8 MPa Flatw 80*10*4 sp=64mm 205 ISO 75/Af
PHYSICAL Value Unit Standard
Specific Gravity 1.54 - ASTM D 792
Mold Shrinkage,flow,3.2mm(5) 0.5-0.7 % SABIC Method
Melt Flow Rate,250℃/5.0 kgf 52 g/10 min ASTM D 1238
Density 1.54 g/cm³ ISO 1183
Water Absorption,(23℃/sat) 0.09 % ISO 62
Moisture Absorption(23℃/50% RH) 0.1 % ISO 62
Melt Volume Rate,MVR at 250℃/5.0 kg 38 cm³/10 min ISO 1133
Source GMD,last updated:2008/11/19
Parameter Injection Molding Value Unit
Drying Temperature 120
Drying Time 3-4 hrs
Drying Time(Cumulative) 12 hrs
Maximum Moisture Content 0.02 %
Melt Temperature 250-265
Nozzle Temperature 245-260
Front-Zone 3 Temperature 250-265
Middle-Zone 2 Temperature 245-260
Rear-Zone 1 Temperature 240-255
Mold Temperature 65-90
Back Pressure 0.3-0.7 MPa
Screw Speed 50-80 rpm
Shot to Cylinder Size 40-80 %
Vent Depth 0.025-0.038 mm
Source GMD,last updated:2008/11/19

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics

1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.POM A25-03 高刚性
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

关健字:【Valox* Resin PBT IQ420HP