快速查找
主营塑料
产品推荐
- ⊕PPS OL003A 含玻璃纤维,聚四氟乙
- ⊕PBT 420SE0 玻纤30%增强,阻燃级
- ⊕PBT 310SE0 非增强型,PBT阻燃树脂
- ⊕PP HJ730 高流动,高钢性,高耐热
- ⊕PP FB71U6 耐热级,抗UV,阻燃级
- ⊕PA6 73G30L NC010 玻璃纤维30%增
- ⊕PA66 70G43L NC010 玻璃纤维43%增
- ⊕PA66 70G33L NC010 玻璃纤维33%增
- ⊕PA66 70G30L NC010 玻璃纤维30%增
- ⊕PA66 80G33L NC010 玻纤33%增强,
- ⊕PA66 FR50 NC010A 玻纤25%增强,阻
- ⊕POM 900P NC010 低粘度,热稳定,低
- ⊕POM 500P NC010 中高粘,热稳定,低
- ⊕POM 100P NC010 高粘度,韧性好,热
- ⊕PBT SK605 NC010 玻璃纤维30%增强
- ⊕PA66 1300G 玻纤增强级
联系我们
LNP Lubricomp* Polyamides Compound
Enhanced wear resistance, lower friction in tough
Polyamide-based LNP Lubricomp compounds provide these tough resins with improved wear resistance and lower friction by combining them with internal lubricants. Glass and carbon fibers can also be included for improved strength and stiffness.
LNP™ Lubricomp™ Compound PA66 RFP36 塑料数据
Also known as:LNP™ Lubricomp™ Compound RFL-4536
Product reorder name:RFP36
LNP* Lubricomp* RFP36 is a compound based on Nylon 66 resin containing Glass Fiber, PTFE, Silicone. Added features of this material include: Internally Lubricated. This product is also known as Lubricomp* RFL-4536.
MECHANICAL | Value | Unit | Standard |
Tensile Modulus,50mm/min | 106800 | kgf/cm² | ASTM D 638 |
Flexural Stress | 1980 | kgf/cm² | ASTM D 790 |
Flexural Modulus | 77200 | kgf/cm² | ASTM D 790 |
Tensile Modulus,1mm/min | 9800 | MPa | ISO 527 |
IMPACT | Value | Unit | Standard |
Izod Impact,unnotched,23℃ | 79 | cm-kgf/cm | ASTM D 4812 |
Izod Impact,notched,23℃ | 14 | cm-kgf/cm | ASTM D 256 |
Instrumented Impact Energy @ peak,23℃ | 71 | cm-kgf | ASTM D 3763 |
Multiaxial Impact | 50 | cm-kgf | ISO 6603 |
Izod Impact,unnotched 80*10*4 +23℃ | 50 | kJ/m² | ISO 180/1U |
Izod Impact,notched 80*10*4 +23℃ | 9 | kJ/m² | ISO 180/1A |
THERMAL | Value | Unit | Standard |
HDT,1.82 MPa,3.2mm,unannealed | 233 | ℃ | ASTM D 648 |
HDT/Af,1.8 MPa Flatw 80*10*4 sp=64mm | 236 | ℃ | ISO 75/Af |
PHYSICAL | Value | Unit | Standard |
Density | 1.48 | g/cm³ | ASTM D 792 |
Moisture Absorption,50% RH,24 hrs | 0.78 | % | ASTM D 570 |
Mold Shrinkage,flow,24 hrs(5) | 0.2 | % | ASTM D 955 |
Mold Shrinkage,xflow,24 hrs(5) | 1 | % | ASTM D 955 |
Mold Shrinkage,flow,24 hrs(5) | 0.21 | % | ISO 294 |
Mold Shrinkage,xflow,24 hrs(5) | 0.97 | % | ISO 294 |
Wear Factor Washer | 11 | 10^-10 in^5-min/ft-lb-hr | ASTM D 3702 Modified |
Dynamic COF | 0.56 | - | ASTM D 3702 Modified |
Static COF | 0.48 | - | ASTM D 3702 Modified |
Density | 1.48 | g/cm³ | ISO 1183 |
Moisture Absorption(23℃/50% RH) | 1.22 | % | ISO 62 |
FLAME CHARACTERISTICS | Value | Unit | Standard |
UL Compliant,94HB Flame Class Rating(3)(4) | 1.5 | mm | UL 94 by SABIC-IP |
Source GMD,last updated:2008/10/10 |
Parameter Injection Molding | Value | Unit |
Drying Temperature | 80 | ℃ |
Drying Time | 4 | hrs |
Maximum Moisture Content | 0.15-0.25 | % |
Melt Temperature | 280-305 | ℃ |
Front-Zone 3 Temperature | 295-305 | ℃ |
Middle-Zone 2 Temperature | 280-295 | ℃ |
Rear-Zone 1 Temperature | 265-275 | ℃ |
Mold Temperature | 95-110 | ℃ |
Back Pressure | 0.2-0.3 | MPa |
Screw Speed | 30-60 | rpm |
Source GMD,last updated:2008/10/10 |
THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics
1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
关健字:【LNP™ Lubricomp™ Compound PA66 RFP36】