旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PA6 PFI12R 含玻璃纤维,硅酮,内部润滑,易脱模
  • 产 品:PA6 PFI12R 含玻璃纤维,硅酮,内部润滑,易脱模
  • 产 地:美国液氮
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

LNP* Lubricomp* Compound
LNP Lubricomp Resin All Series
LNP* Lubricomp* compounds provide improved wear resistance and lower friction by combining engineering resins with internal lubricants. Lubricomp compounds, which can also be stiffened with glass or other fiber, can help extend product life and reduce or eliminate squeaks and other noise from moving parts. LNP specialty compound offerings are available in a broad portfolio of standard and engineering materials.

LNP™ Lubricomp™ Compound PA6 PFI12R 塑料数据

Also known as:LNP™ Lubricomp™ Compound PFL-4412 MR
Product reorder name:PFI12R
LNP* Lubricomp* PFI12R is a compound based on Nylon 6 resin containing Glass Fiber, Silicone. Added features of this material include: Internally Lubricated, Mold Release.

MECHANICAL Value Unit Standard
Tensile Stress,break 1070 kgf/cm² ASTM D 638
Tensile Strain,break 3.2 % ASTM D 638
Tensile Modulus,50mm/min 50500 kgf/cm² ASTM D 638
Flexural Stress 1540 kgf/cm² ASTM D 790
Flexural Modulus 53500 kgf/cm² ASTM D 790
IMPACT Value Unit Standard
Izod Impact,unnotched,23℃ 72 cm-kgf/cm ASTM D 4812
Izod Impact,notched,23℃ 5 cm-kgf/cm ASTM D 256
THERMAL Value Unit Standard
HDT,1.82 MPa,3.2mm,unannealed 202 ASTM D 648
PHYSICAL Value Unit Standard
Density 1.19 g/cm³ ASTM D 792
Mold Shrinkage,flow,24 hrs(5) 0.5 % ASTM D 955
Source GMD,last updated:2007/01/02
Parameter Injection Molding Value Unit
Drying Temperature 80
Drying Time 4 hrs
Maximum Moisture Content 0.15-0.25 %
Melt Temperature 265-275
Front-Zone 3 Temperature 275-290
Middle-Zone 2 Temperature 265-275
Rear-Zone 1 Temperature 250-260
Mold Temperature 80-95
Back Pressure 0.3-0.7 MPa
Screw Speed 30-60 rpm
Source GMD,last updated:2007/01/0

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics

1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

关健字:【LNP™ Lubricomp™ Compound PA6 PFI12R